pageimage

ZSLV Series

  • Features
  • Details
  • Type Overview

Features

Specially designed for testing fuel cells
• Voltage up to 20 V
ZSLV Serie
• Current up to 2,250 A
• Power 1,000 W ... 6,000 W
• Full current at 150 mV ... 200 mV input voltage
• Current, voltage, resistance, power mode
• Dynamic loads
• SCPI programming with measurement function
• Electronic protection
• Analog measurement outputs for voltage, current and power
• Analog control input
• Dynamic function with synchronized data logging

 

Details

Operating Modes
The ZSLC series electronic loads have the four operating modes constant current, voltage, power and resistance. In addition, depending on the operating mode limit values can be set for the maximum permissible current and the minimum permissible voltage.

To increase the resolution for each device, along with the full setting range, a reduced setting of 1/3 of the rated current is available. The load can be preset even without a connected test unit. The display then shows the values directly in amps, ohms, volts or watts.

Dynamic and Control Time
The inbuilt modular enables two independently-adjustable currents and times from 100 μs ... 1 s. The control speed of the devices can be adjusted to the test unit in three stages (fast - medium - slow).

Protective Devices
The following protective devices are built in:

  • Over-current protection
  • Over-power protection
  • Over-temperature protection
  • Protection of the GND lines on the Analog I/O interface

Voltage Switching
A trigger voltage can be set for peak-free voltage hook-up. The current is enabled when the input voltage exceeds the trigger voltage.

Overload Capacity
Depending on the model the devices have temporary overload capacity. The level and duration of the possible overload depends on the operating temperature of the output stage. 
The device can therefore be used for significantly higher performance tasks.

Remote Control
Most the load functions can be controlled remotely via Analog I/O Interface. The control inputs can be operated with TTL levels and 24 V from PLC controllers.

A version (ZS06) which is electrically isolated from the load input is optionally available.

Analog Control
In the operating modes CC, CV and CP the setting value can be controlled by 0...5 V or 0...10 V DC.

Analog Measurement Outputs
There are 0...10 V analog  measurement signals available for voltage, current and power. The GND terminals can float ±2 V with respect to the negative load input (also optionally isolated - Option ZS06).

Cooling
The units are air-cooled. To keep the operating noise low, the fans are controlled depending on temperature and current. For better utilization of the maximum possible overload capacity the fans can be set to full power.

Mechanics
The ZSLV is a sturdy 19“ rack design and can also be used as a table-top device.

From 5 height units there are retractable handles on the top of the device.
Optional castors can be mounted on heavy devices. No separate installation kits are needed for 19“ rack installation.

Connections
All connections are at the rear side. The current connections are solid copper rails with screw connectors.

Safety
Covers are available as contact protection for units for dangerous contact voltages.

Interfaces (optional)


  • RS-232 + USB
  • GPIB
  • Ethernet-RS-232 Converter
  • System Interface Cabel or Fiber Optic
  • Data Acquisition Tool

Hardware Expansions (optional)


  • Electrically Isolated Analog I/O Interface
  • Power I/O Card
  • Analog I/O Extension-Card
  • Temperature Interface
  • Castors
  • Zero-Volt-Option

Factory Calibration Certificate
A Factory Calibration Certificate (FCC) can be supplied with the devices. The FCC meets the requirements according to DIN EN ISO 9000ff. This calibration certificate documents the traceability to national standards to illustrate the physical device in accordance with the international  System of Units  (SI). The recommended calibration interval is 2 years.

Software Tools
The H&H Homepage has a program library for Windows with a controll tool an LabVIEW drivers.

Documentation
We supply a User Manual as pdf file and printed General Safety Instructions, each in German and English.



Type Overview